Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Application of Direct Ignition Technology with Minimum Gasified Oil in Lignite-Fired Boiler

The firing is in the stable condition and the rate of oil saving comes up to 64%, after Fularji Power Plant adopted the technology of minimum gasified oil igniting pulverized lignite directly and the technology of multistage coal combustion with energy amplified stage by stage.     

Flows in rectangular microchannels driven by capillary force and gravity

Capillary phenomena was studied and discussed by the scholars about 200 years ago, but the progress was slow due to the limited equipment and manufacture precision of the microchannel. In recent years, because of the rapid development of MEMS and micromachining, many applications of the capillary flow is widely developing in some modern processes, such as underfilling of flip chip, flow in microfluidic chip or biochip, and a variety of other fields.     

如何又好又快地完成水利统计任务

1.依法进行统计是统计工作的根本 《中华人民共和国统计法》的颁布实施为统计工作提供了有力的法律保证,它明确了部门统计的合法性、必要性,明确了其责任、权力和义务。统计工作必须在统计法允许的范围内开展。设置统计机构,配备统计人员,确定统计任务,制定统计报表制度,进行各项统计调查,确定具体的统计指标等,都必须遵循这一原则。[第一段]     

中频反应溅射SiO2膜与直流溅射ITO膜的在线联镀

多数ITO透明导电玻璃生产线在实现SiO2膜与ITO膜在线联镀时，应用SiO2靶射频溅射沉积SiO2膜工艺和ITO靶直流溅射沉积ITO膜工艺，如果SiO2膜应用硅靶反应磁控溅射工艺，存在这种工艺是否可以与ITO靶直流溅射沉积ITO膜工艺在线联用以及如何实现联用的问题。作者对现有的生产线进行了改造设计、加工，做了大量实验、质谱分析和多项测试研究，成功地实现反应溅射SiO2膜与ITO膜在线联镀，做到SiO2镀膜室的工作状态的变化基本上不影响ITO镀膜室的工艺条件。     

川中丘陵区一种新型小流域径流输沙模型的建立与应用

径流输沙模型对定量评价水沙的输出响应具有重要的意义。本研究在已有研究成果的基础上，通过对四川盐亭县林山西沟小流域的径流、泥沙进行现场观测与分析，提出含沙量单位线的定义及其确定方法，建立了适应该小流域的径流输沙模型。并应用实测资料进行比较，表明模型的模拟结果可靠，模拟过程确定性系数达0．8以上，为川中丘陵区小流域径流输沙过程的预测预报提供了一个新方法。     

MPLS交换路由器的设计与实现

MPLS是目前Internet核心网上最看好的技术，基于Crossbar的高速交换技术的发展也很快，但是如何实现2种技术的有机结合以到达最优的性能却有一系列问题需要考虑。本文结合某MPLS路由器的设计项目，综合考虑了当前MPLS的标准以及有关交换结构的最新技术，对实现MPLS交换路由器进行了深入研究，并详细探讨了高速接口、排除和调度以及Crossbar等关键模块的设计和实现方案。     

HTR-10燃料元件装卸系统冷态调试

10MW高温气冷实验堆（HTR－10）是一座球床堆，由燃料元件装卸系统实现燃料元件的装卸和循环，且不需要停堆，为保证HTR－10的正常运行，燃料元件装卸系统必须安全，可靠，为此，必须对燃料元件装卸系统进行周密，细致的调试试验和验证，本文介绍了燃料元件装卸系统冷调试的主要调试项目，调试方法和调试结果。     

海洋石油平台水下夹桩器本体结构分析

水下夹桩器是一种广泛应用于海洋石油平台建设的液压夹具。水下夹桩器本体焊接在导管架上，支撑夹桩器液压缸。在水下夹桩器本体设计中，采用有限元法完成了对本体强度和刚度的结构分析；建立了有限元分析模型，用ANSYS软件进行结构分析，得到了分析结果，并将该结果与理论计算结果进行了比较，验证了有限元分析技术的有效性。设计结果满足工程要求，为改进和优化结构提供了理论依据，节省了分析计算时间。